Search Results

The VanDyne SuperTurbocharger (SuperTurbo) is a turbocharger with an integral Continuously Variable Transmission (CVT). By changing the gear ratio of the CVT, the SuperTurbo is able to either pull power from the crankshaft to provide a supercharging function, or to function as a turbo-compounder, where energy is taken from the turbine and given to the crankshaft. The SuperTurbo's supercharger function enhances the transient response of a downsized and turbocharged engine, and the turbo-compounding function offers the opportunity to extract the available exhaust energy from the turbine rather than opening a waste gate. Using 1-D simulation, it was shown that a 2.0-liter L4 could exceed the torque curve of a 3.2L V6 using a SuperTurbo, and meet the torque curve of a 4.2-liter V8 with a SuperTurbo and a fresh-air bypass configuration. In each case, the part-load efficiency while using the SuperTurbo was better than the baseline engine.

The equipment for collecting dilute exhaust samples involves the use of bag materials (i.e., Tedlar®) that emit hydrocarbons that contaminate samples. This study identifies a list of materials and treatments to produce bags that reduce contamination. Based on the average emission rates, baked Tedlar®, Capran® treated with alumina deposition, supercritical CO2 extracted Kynar® and supercritical CO2 extracted Teflon NXT are capable of achieving the target hydrocarbon emission rate of less than 15 ppbC per 30 minutes. CO2 permeation tests were also performed. Tedlar, Capran, Kynar and Teflon NXT showed comparable average permeation rates. Based on the criteria of HC emission performance, changes in measured CO2 concentration, ease of sealing, and ease of surface treatment, none of the four materials could be distinguished from one another.

In-cylinder ion sensing through sparkplug electrodes can be used to determine in-cylinder A/F ratio by using a modified production coil-on-plug ignition system having ion sensing capability. The in-cylinder ionization can be characterized by the height of the peak, location of the peak from ignition command and area under the ionization signal curve. The effects of A/F ratio on the in-cylinder ionization can be isolated from other affecting factors by conducting tests on a constant volume combustion device in which the initial pressure and temperature can be well controlled. This results in a parabolic correlation of the ionization characteristics with the mixture equivalence ratio. Additionally the ionization characteristics show strong dependence on engine load and speed. Equivalence ratio characteristics during engine cranking and warm up are investigated, and a method for on-line calibration of ionization detection is discussed.

A technique was developed for measuring the Laminar Burning Velocity (LBV) of multi-component fuel blends for use in high-performance spark-ignition engines. This technique involves the use of a centrally-ignited spherical combustion chamber, and a complementary analysis code. The technique was validated by examining several single-component fuels, and the computational procedure was extended to handle multi-component fuels without requiring detailed knowledge of their chemical composition. Experiments performed on an instrumented high-speed engine showed good agreement between the observed heat-release rates of the fuels and their predicted ranking based on the measured LBV parameters.

A study was performed to develop optimum design strategies for a production V6 engine to maximize catalyst performance at minimum pressure loss and at minimum cost. Test results for an advanced system, designed to meet future emission limits on a production V6 vehicle, are presented based on FTP testing. The on-line pressure loss and temperature data serves to explain the functioning of the catalyst.

Real-time transient and steady-state oil consumption were measured on three SI-engines, applying two different ring-packs to each engine. Testing of multiple engines enables an assessment of the engine-to-engine variability in oil consumption. Testing of multiple ring-packs on each engine enables an assessment of the ring-pack-to-ring-pack variability in oil consumption. The oil consumption was measured by the Southwest Research Institute (SwRI) novel developed SO2-tracer technique, referred to as RTOC-III. An interesting finding is that the testing shows low engine-to-engine and ring-pack-to-ring-pack variability, in both steady-state, as well as in transient oil consumption. This suggests that the RTOC-III system did not introduce significant variability to the data. The testing results are experimental verification of a design and simulation exercise, in a field of scarcely published literature.

The Tank-Automotive RD&E Center periodically conducts foreign materiel evaluations to assess the current state of the art for ground vehicle technologies. The Propulsion Laboratory is conducting performance evaluations of an opposed-piston two-stroke diesel tank engine produced by the Kharkov Design Bureau in Ukraine. A key factor in the performance of all two-stroke engines is the scavenging process, which determines how well the cylinders are emptied of exhaust and filled with fresh air. The overall air flow rate is not sufficient to determine this, as a significant amount of air may be lost through the exhaust ports during the scavenging process. The inlet tracer gas method was employed to provide the additional data required. With methane as the tracer, it produced reasonable and consistent data over a wide range of engine speeds and loads. The inlet tracer gas method was found to be an effective tool for measuring the scavenging performance of a running two-stroke diesel engine.

The current operation of the International Space Station (ISS) calls for the oxygen used by the occupants to be vented overboard in the form of CO2, after the CO2 is scrubbed from the cabin air. Likewise, H2 produced via electrolysis in the oxygen generator is also vented. NASA is investigating the use of the Sabatier process to combine these two product streams to form water and methane. The water is then used in the oxygen generator, thereby conserving this valuable resource. One of the technical challenges to developing the Sabatier reactor is transferring CO2 from the Carbon Dioxide Removal Assembly (CDRA) to the Sabatier reactor at the required rate, even though the CDRA and the Sabatier reactor operate on different schedules. One possible way to transfer and store CO2 is to use a mechanical compressor and a storage tank.

The effect of low temperature intake air on the knock limited brake mean effective pressure (BMEP) in a spark ignited natural gas engine is described in this paper. This work was conducted to demonstrate the feasibility of using the vaporization of liquefied natural gas (LNG) to reduce the intake air temperature of engines operating on LNG fuel. The effect on steady-state emissions and transient response are also reported. Three different intake air temperatures were tested and evaluated as to their impact upon engine performance and gaseous emissions output. The results of these tests are as follows. The reduced intake air temperature allowed for a 30.7% (501 kPa) increase in the knock-limited BMEP (comparing the 10°C (50°F) intake air results with the 54.4°C (130°F) results). Exhaust emissions were recorded at constant BMEP for varying intake air temperatures.

In off-highway applications the engine torque is distributed between the transmission (propulsion) and other accessories such as power steering, air conditioning and implements. Electronic controls offer the opportunity to more efficiently manage the control of the engine and transmission as an integrated system. This paper deals with development of a steepest descent algorithm for maximizing the efficiency of hydrostatic transmission along with the engine in the presence of accessory load. The methodology is illustrated with an example. The strategy can be extended to the full hydro-mechanical configuration as required. Applications of this approach include adjusting for component wear and intelligent energy management between different accessories for possible size reduction of powertrain components. The potential benefits of this strategy are improved fuel efficiency and operator productivity.

Vehicle designers make use of vehicle performance programs such as RAPTOR™ to predict the performance of concept vehicles over ranges of industry standard drive cycles. However, the accuracy of such predictions may be greatly influenced by factors requiring more specialist simulation capabilities. For example, fuel economy prediction will be heavily influenced by the performance of the engine cooling system and its impact on the vehicle's aerodynamic drag, and the load from the air-conditioning system. To improve the predictions, specialist simulation capabilities need to be applied to these aspects, and brought together with the vehicle performance calculations through co-simulation. This paper describes the approach used to enable this cosimulation and the benefits achieved by the vehicle designer.

Two different laboratory fuel-injection-pump durability-tests were conducted with four advanced technology test fuels. The first test used a relatively low pressure rotary, opposed piston fuel injection pump similar to those used on some current North American engines. The second test used a relatively high pressure common rail injection pump such as those used currently on some European engines. The tests were scheduled to operate for 500 hours under severe load conditions. It can be concluded that the common-rail, high-pressure fuel pump is more sensitive to the advanced fuels than is the rotary pump in this severe duty-cycle test. Although the laboratory high frequency reciprocating rig (HFRR) tests were able to distinguish between those fuels that contained lubricity additives and those that did not, there was little correlation with pump durability results.

This oil category was driven by two new cooled exhaust gas recirculation (EGR) engine tests operating with 15% EGR, with used oil soot levels at the end of the test ranging from 6 to 9%. These tests are the Mack T-10 and Cummins M11 EGR, which address ring, cylinder liner, bearing, and valve train wear; filter plugging, and sludge. In addition to these two new EGR tests, there is a Caterpillar single-cylinder test without EGR which measures piston deposits and oil consumption control using an articulated piston. This test is called the Caterpillar 1R and is included in the existing Global DHD-1 specification. In total, the API CI-4 category includes eight fired-engine tests and seven bench tests covering all the engine oil parameters. The new bench tests include a seal compatibility test for fresh oils and a low temperature pumpability test for used oils containing 5% soot. This paper provides a review of the all the tests, matrix results, and limits for this new oil category.

It has been shown within the catalyst industry that the emission performance with higher cell density technology and therefore with higher specific geometric area is improved. The focus of this study was to compare the overall performance of high cell density catalysts, up to 1600cpsi, using a MY 2001 production vehicle with a 4.7ltr.V8 engine. The substrates were configured to be on the edge of the design capability. The goal was to develop cost optimized systems with similar emission and back pressure performance, which meet physical and production requirements. This paper will present the results of a preliminary computer simulation study and the final emission testing of a production vehicle. For the pre-evaluation a numerical simulation model was used to compare the light-off performance of different substrate designs in the cold start portion of the FTP test cycle.

The use of small-hole diesel injector tips and high injection pressures was investigated as a countermeasure to the increased particulate matter (PM) emissions formed when using exhaust gas recirculation (EGR) in diesel engines. This study examined the use of injector tip hole sizes down to about 0.09-mm (0.0035 in.), and injection pressures to 300 MPa (3000 bar, or 43,500 psi). The first phase of these studies was conducted in a high-temperature, high-pressure combustion bomb, with supporting calculations using a unit injector model, a jet-mixing model, and a diesel jet evaporation model. The second phase was conducted in a commercial diesel engine of 12.7-liter displacement designed to meet U.S. 1998 emissions levels. Engine tests were conducted with a baseline cam and a faster rise-rate cam, and three different hole tip sizes. The cams consisted of a baseline cam and a cam of similar design, but with a 12 percent faster rise rate.

This paper describes the development of a generic test cell software designed to overcome many vehicle-component testing difficulties by introducing modern, real-time control and simulation capabilities directly to laboratory test environments. Successfully demonstrated in a transmission test cell system, this software eliminated the need for internal combustion engines (ICE) and test-track vehicles. It incorporated the control of an advanced AC induction motor that electrically simulated the ICE and a DC dynamometer that electrically replicated vehicle loads. Engine behaviors controlled by the software included not only the average crankshaft torque production but also engine inertia and firing pulses, particularly during shifts. Vehicle loads included rolling resistance, aerodynamic drag, grade, and more importantly, vehicle inertia corresponding to sport utility, light truck, or passenger cars.

The objective was to demonstrate the feasibility of operating a natural gas two-stroke engine using glow plug ignition with very lean mixtures. Based on the results obtained, the term SCGI (stratified charge glow plug ignition) was coined to describe the engine. An JLO two-stroke diesel engine was converted first to a natural gas fueled spark-ignited engine for the baseline tests, and then to an SCGI engine. The SCGI engine used a gas operated valve in the cylinder head to admit the natural gas fuel, and a glow plug was used as a means to initiate the combustion. The engine was successfully run, but was found to be sensitive to various conditions such as the glow plug temperature. The engine would run very lean, to an overall equivalence ratio of 0.33, offering the potential of good fuel economy and low NOx emissions.

An on-line oil consumption measurement system using the SO2 tracer method has characterized automotive gasoline engine oil consumption under various engine operating conditions, including a 200-hour durability test. An oil consumption map of total engine, individual cylinder, and valve train was produced for various speed and load ranges under both steady-state and step-transient operating conditions. The effect of spark timing as an additional engine parameter on the oil consumption was also investigated. Oil consumption maps have enlightened the conventional understanding of oil consumption characteristics and broadened the areas of concern for control technologies. This paper reports the benefit of the on-line oil consumption measurement system, the result of oil consumption history over the durability test, discrete measurement of oil consumption contribution within the engine, and various oil consumption characteristics affected by engine operating conditions.

This paper describes the results of using the Southwest Research Institute (SwRI) engine friction model to examine the effects of changing certain design parameters on the friction of a gasoline engine. The paper gives the results of an examination of the effects of changing the main and cam-shaft bearing aspect ratio on the friction of those bearings, and the effect of the tension of the piston rings, and the gas loading on them. The model predicts that the friction of the piston rings is the highest single component in the friction, except at high engine speeds, where the predicted windage was greater. Next, after the piston rings, was the piston skirt friction. The remaining components were relatively small, and in order of importance were the accessories, the cam bearing friction, cam/tappet friction, the main bearing, the crank pin, and oscillatory friction in the valve train, in that order.

This paper describes the findings of a laboratory effort to demonstrate improved automotive exhaust emission control with a cold-start hydrocarbon collection system. The emission control strategy developed in this study incorporated a zeolite molecular sieve in the exhaust system to collect cold-start hydrocarbons for subsequent release to an active catalytic converter. A prototype emission control system was designed and tested on a gasoline-fueled vehicle. Continuous raw exhaust emission measurements upstream and downstream of the zeolite molecular sieve revealed collection, storage, and release of cold-start hydrocarbons. Federal Test Procedure (FTP) emission results show a 35 percent reduction in hydrocarbons emitted during the cold-transient segment (Bag 1) due to adsorption by the zeolite.